Fort Lauderdale, FL – Popular Honeywell online retailer DtiCorp.com
(http://www.DtiCorp.com) is introducing 8 Brand New Honeywell C7061
Flame Sensors. Dynamic self-checking flame detector used with R7861
Dynamic Self-check Amplifiers for sensing the ultraviolet radiation
generated by the combustion of gas, oil, or other fuels. The C7061A is a
dynamic self-checking flame detector for
sensing the ultraviolet radiation generated by the combustion of gas,
oil, or other fuels. This flame detector is available in two versions:
model C7061A for use in Standard applications, and model C7061F for use
in installations requiring explosion-proof packaging. The flame detector
is designed for use with either, R7061 Dynamic Self-Check Ultraviolet
amplifier and R4348 Flame Switch or R7861A Dynamic Self-Check
Ultraviolet amplifier and 7800 SERIES Burner Programmers. These
configurations provide a closed-loop, self-checking circuit which
insures the integrity of both amplifier and flame detector. Improper
response simulated flame loss results in a safety shutdown and/or alarm.
Features:
- Oscillating shutter interrupts ultraviolet radiation reaching the UV sensor to provide the UV sensor tube checking function.
- Can be mounted horizontally, vertically or at any angle in between.
- The detector requires faceplate alignment and has integral locating
reference points to assure proper operation of the shutter mechanism.
- Field replaceable ultraviolet sensing tube and quartz viewing window.
- Models with threaded conduit fitting and color-coded leadwires allow rapid electrical installation.
- C7061A1038 or A1046 5 pin Brad Harrison type (formally 41307N) mating connector not supplied nor available through Honeywell.
- Two detectors can be wired in parallel to reduce nuisance shutdowns in difficult flame sighting applications.
- Protective heat block built into mounting flange.
- Minus 40 F (-40 C) rated ultraviolet sensing tube is supplied.
- C7061E meets NEMA 4 standards with viewing window rated to 20 psi.
- C7061F has an explosion-proof housing for use in hazardous atmospheres with a viewing window rated to 100 psi.
Specifications:
- Models
C7061A: Self checking UV flame detector in standard housing.
C7061F: Self checking UV flame detector in explosion proof housing.
Designed for use with either R7061 Dynamic Self-Check Ultraviolet
amplifier and R4348 Flame Switch or with R7861A Dynamic Self-Check
Ultraviolet amplifier and 7800 SERIES Burner Programmers
- Ambient Operating temperature ratings
C7061A: -40°C to +70°C (-40°F to +160°F)“(derate ambient 1°F for every 13°F of aspirator temperature over 160°F).
C7061F: -20°C to +70°C (-22°F to +160°F)
- Storage temperature ratings:
Minus 51°C to +85°C (-60°F to +185°F)
- Voltage and Frequency:
C7061A1004 120 VAC, 50/60 Hz
C7061A1020 115/230 VAC, 50/60 Hz
C7061F1003 115/230 VAC, 50/60 Hz
The System operates correctly at a nominal voltage (-15%, +10%), 50/60 Hz.
- Flame Signal:
Measured at the flame current meter jack.
C7061 Detector: 1.4 to 5.5 micro amps (nominal).
R7061A Amplifier: 2.5 to 5.5 micro amps (nominal).
R7861A Amplifier: 1.25 to 5.0 Volts (On keyboard display module).
- Flame Signal amplifier:
R7061A Dynamic Self-Check Ultraviolet amplifier
R7861A Dynamic Self-Check Ultraviolet amplifier
- Interchangeability:
Models C7061A and C7061F are not interchangeable with other flame detector models.
- Shutter frequency:
0.2 Hz, nominal (when used in combination with 7800 SERIE).
Interrupts the line-of-sight of the detector about 12 times per minute
to provide self-checking. Any malfunction in the flame detection system
results in a safety shutdown. 1Hz nominal when used with R4348 in
combination with R7061 amplifier.
- Pressure rating of quarz viewing window:
C7061A: 138 kPa (20 psi) maximum.
C7061F: 690 kPa (100 psi) maximum
- Enclosure
C7061A: Meets IP66 enclosure requirements (indoor, outdoor protection;
rain-tight, dust-tight, hosedirected water). Optional water jacket
available.
C7061F: IP65 according to DIN 40050
- Weight
C7061A: 3.3 kg (7.3 Ib)
C7061F: 6.3 kg (13.9 Ib)
- Mounting and orientation
C7061A : Mounting flange with 3/4 inch NPT internal threads for attaching to sight pipe.
C7061F: Mounting flange with 1 inch NPT internal threads for attaching to sight pipe.
- Wiring Connections
C7061A1004: NEC Class 1 color coded leadwire.
Length: 8 ft (2.4m).
C7061A1020: Terminal block.
Threaded leadwire opening in faceplate:
1/2-14 NPSM internal threads for attaching conduit.
One brass cable gland standard with housing.
- Serviceability:
Field replaceable viewing window and ultraviolet sensing tube, coil and shutter assembly.
- Maximum cable length:
300 meter between sensor and amplifier
- Approvals:
Underwriters Laboratories Inc. Listed.
Canadian Standards Association Certified: Master File LR95329-1.
Factory Mutual Approved: 14740.01.
lndustrial Risk Insurers Acceptable.
Models available:
1. C7061A1004, 120 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking
2. C7061A1012, 120 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking
3. C7061A1020, 120 or 230 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking
4. C7061A1038, 120 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking
5. C7061A1046, 120 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking
6. C7061A1053, 120 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking
7. C7061F1003, 120/230 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking, Explosion Proof
8. C7061F2001, 120 Vac Flame Sensor, Ultraviolet, Purple Peeper, Self-Checking, Explosion Proof
About Us: DtiCorp.Com (http://www.DtiCorp.com) carries more than
35,000 HVAC products, including industrial, commercial and residential
parts and equipment from Honeywell, Johnson Contols, Robertshaw, Jandy,
Grundfos, Armstrong and more. Our online catalog is easy to navigate and
search, and all products have a picture and a description. If a
customer has any questions about a product, they can call 800-757-5999
and speak with one of our product experts. Our mission is to offer the
best prices anywhere to our customers.
Julian Arhire
Manager DtiCorp.com
Phone: 954.484.2929
Fax: 954.206.0767
Web: http://www.DtiCorp.com
