Fort Lauderdale, FL - Popular Honeywell online retailer DtiCorp.com (http://www.DtiCorp.com) is introducing 22 brand new Honeywell Series 90 Modutrol IV Motors.
The Honeywell Series 90 Modutrol IV Motors are spring return and
non-spring return modulating proportional control motors. Use these
motors with controllers that provide a Series 90 output to operate
dampers or valves. When replacing a motor in a valve application, the
linkage determines the necessity of the 220738A Adapter Bracket. With
Q100, Q601 or Q618 Linkages, it is necessary to use the 220738A to raise
the motor shaft to the appropriate height. Valve applications with a
Q5001 Linkage do not require the 220738A Adapter Bracket. To operate
Honeywell V5011 two- way or V5013 three-way valves through full stroke,
use a 160° stroke motor.
Features:
- Directly replaces M934A,D, M941, M944A,C,D, M945A,D,F, M954, M965, and M975 motors.
- Oil-immersed motor and gear train for reliable performance and long life.
- Integral junction box provides NEMA 3 weather protection.
- Motor and circuitry operate from 24 Vac. Models available with factory
installed transformer, or a field-added internal transformer.
- Quick-connect terminals standard—screw terminal adapter available.
- Adapter bracket for matching shaft height of older motors standard with TRADELINE motors.
- Field adjustable stroke (90° to 160°) models available.
- Nominal timing of 30 seconds for 90° stroke and 60 seconds for 160° stroke standard. Other timings available.
- Die-cast aluminum housing.
- Integral auxiliary switches available factory mounted, or can be field added to TRADELINE® models.
- Integral spring returns motor shaft to normal position (fully open or
fully closed, depending on model) upon power interruption.
- Field addable interface modules can be mounted in the junction box to upgrade the motor to Series 70 (electronic) control.
- TRADELINE spring return motors can operate valve linkages from power
end or auxiliary end shafts for normally closed or normally open valve
applications.
Specifications:
- Designed for flame safeguard applications in commercial/industrial oil or gas burner system.
- Vibration resistant electronic drive circuit.
- Regulated by three-wire proportional controller.
- Stroke is field-adjustable to 90 or 160 degrees.
- Power or Auxiliary End: 200 lb (90.8 kg) maximum.
- Maximum Combined Load: 300 lb (136 kg).
- Maximum: 150°F (66°C) at 25% duty cycle.
- Minimum: Minus 40°F (-40°C).
- Crankshaft: 3/8 in. (9.5 mm) Square.
- Controller Type: 135 ohm, Series 90 proportioning
controller. Series 90 high or low limit controller with manual minimum
position potentiometer (with a combined total resistance of up to 500
ohms) can also be used in the control circuit.
- Motor Rotation: Normally closed. (The normal position is the position
the motor assumes with controller disconnected.) The closed position is
the limit of counterclockwise rotation as viewed from the power end of
the motor. Motor opens clockwise (as viewed from the power end). Motors
are shipped in the closed position.
- Stroke: Field adjustable from 90° to 160°. Start position of shaft
changes with adjustment of stroke. (Midpoint of stroke remains fixed as
stroke is adjusted.) Stroke is adjusted using cams located in wiring
compartment. Motors are shipped with stroke set at 90°.
- Underwriters Laboratories Inc. Listed: File No. E4436, Guide No. XAPX.
- Canadian Standards Association Certified: General Listing File No. LR1620, Guide No. 400-E.
- Timing And Torque: Motors with 2 min. timing at 90° stroke or 4 min.
timing at 160° stroke contain on-off pulsing circuitry to achieve
timing. Intermittent operation is normal.
Models available:
1. M9164A1005 120V Non-Spring Return Foot Mounted Actuator with 35 lb-in. torque
2. M9164A1013 24/120/230 V Non-Spring Return Foot Mounted Actuator with 75 lb-in. torque
3. M9164A1070 24V Non-Spring Return Foot Mounted Actuator with 35 lb-in. torque
4. M9164C1001 24V Non-Spring Return Foot Mounted Actuator with 35 lb-in. torque
5. M9164C1068 120V Non-Spring Return Foot Mounted Actuator with 35 lb-in. torque
6. M9164D1009 24V Non-Spring Return Foot Mounted Actuator with 35 lb-in. torque
7. M9174B1027 120V Non-Spring Return Foot Mounted Actuator with 75 lb-in. torque
8. M9174C1025 120V Non-Spring Return Foot Mounted Actuator with 75 lb-in. torque
9. M9174C1033 120V Non-Spring Return Foot Mounted Actuator with 75 lb-in. torque
10. M9174D1007 24V Non-Spring Return Foot Mounted Actuator with 75 lb-in. torque
11. M9182A1011 24V Spring Return Foot Mounted Actuator with 60 lb-in. torque
12. M9184A1019 24V Non-Spring Return Foot Mounted Actuator with 150 lb-in. torque
13. M9194D1003 24V Non-Spring Return Foot Mounted Actuator with 300 lb-in. torque
14. M9194E1000 24V Non-Spring Return Foot Mounted Actuator with 300 lb-in. torque
15. M9174F1001 24V Non-Spring Return Foot Mounted Actuator with 75 lb-in. torque
16. M9185F1002 24V Spring Return Foot Mounted Actuator with 60 lb-in. torque
17. M9484D1010 24 Vac Modutrol IV Motor with 150 lb-in torque rating
18. M9484E1009 24 Vac Modutrol IV Motor with 75 lb-in torque rating
19. M9484E1017 24 Vac Modutrol IV Motor with 150 lb-in torque rating
20. M9494D1000 24 Vac Modutrol IV Motor with 300 lb-in torque rating
21. M9494F1003 24 Vac Modutrol IV Motor with 300 lb-in torque rating
22. M9484F1057 24 Vac Modutrol IV Motor with 150 lb-in torque rating
About Us: DtiCorp.Com (http://www.DtiCorp.com)
carries more than 35,000 HVAC products, including industrial,
commercial and residential parts and equipment from Honeywell, Johnson
Contols, Robertshaw, Jandy, Grundfos, Armstrong and more. Our online
catalog is easy to navigate and search, and all products have a picture
and a description. If a customer has any questions about a product,
they can call 800-757-5999 and speak with one of our product experts.
Our mission is to offer the best prices anywhere to our customers.
Julian Arhire
Manager DtiCorp.com
Phone: 954.298.2515
Fax: 954.206.0767
Web: http://www.DtiCorp.com
